Turbosmart BLOW OFF & BYPASS VALVE KITS - Dual Port for: Manual de usuario

Busca en linea o descarga Manual de usuario para Para El Coche Turbosmart BLOW OFF & BYPASS VALVE KITS - Dual Port for: . Turbosmart BLOW OFF & BYPASS VALVE KITS - Dual Port for: Subaru WRX (08+), Liberty_Legacy, Mazdaspeed_MPS 3, 6, CX7 User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 6
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
1
------------------------------------------------------------------------------------------------------------------------
Suitable for: Mazda MPS (Mazdaspeed) 3, 6, CX7, Subaru WRX’08+ (excluding WRX STI 08),
Legacy/Liberty GT’03 - current.
IMPORTANT NOTES:
This Blow-Off Valve does NOT fit the 2008 WRX STi. Please refer to www.turbosmartonline.com for product updates.
Please thoroughly read and understand these instructions before commencing this installation.
The thread on the cap for the vacuum source is AN#3. The standard swivel nipple can be changed to a AN#3 fitting if desired.
RECOMMENDATIONS
Turbosmart recommends that your Blow off valve (BOV) is fitted and adjusted by an appropriately qualified technician
Turbosmart recommends that a boost gauge be permanently fitted to the vehicle
------------------------------------------------------------------------------------------------------------------------
SETTING THE FLANGE TO SUIT DIFFERENT VEHICLES
The BOV flange can be rotated to suit different vehicles. There are currently 2 setting notches; setting notch 1 for the Mazda MPS range
and setting notch 2 for the MY08 WRX/Liberty GT. The BOV comes preset to setting notch 1. The flange can be rotated by loosening
the securing screws at the bottom with a 3mm allen key. Do not remove the screws, only loosen them. Rotate the flange until it lines up
with the desired indicator groove. Re-tighten the screws.
HOW TO INSTALL YOUR BOV
Please check that the following items have been provided in your MPS/WRX Dual port kit.
Quantity
Description
Use
1
MPS/WRX Dual port BOV
MPS/WRX Specific blow off valve
1
Blanking plug
To blank off a port to convert the BOV to full atmospheric or plumb back
1
Gasket
To seal the BOV to the intercooler pipe
1) Installation on a Mazda MPS (Diagrams are from a Mazda 3 MPS) – Setting notch 1
1) Remove the engine cover by removing the two securing screws/plugs.
Product Name: MPS Dual Port
Product Description: Model-Specific Dual Port BOV
Product Number: TS-0205-1009
Setting notches
Indicator Grooves
Vista de pagina 0
1 2 3 4 5 6

Indice de contenidos

Pagina 1 - Indicator Grooves

1 ------------------------------------------------------------------------------------------------------------------------ Suitable for: Mazda MPS (

Pagina 2

2 2) Locate the intake standard BOV. Remove the vacuum/pressure source. 3) Remove the bolts securing the standard BOV and then remove the plumb

Pagina 3 - Setting notch 2

3 2) Installation on a WRX (MY08 Onwards) – Setting notch 2 1. Set the BOV flange to setting notch 2 as per instructions. Locate the standard BOV a

Pagina 4

4 3) Installation on a Liberty GT – Setting notch 2 1) Remove engine cover by removing the 4 securing screws. 2) Locate standard BOV and remove

Pagina 5 - TROUBLE SHOOTING

5 5. Use the factory bolts to fit the new BOV onto the intercooler pipe. Remember to install the supplied gasket in between the BOV flange and the i

Pagina 6

6 TURBOSMART ONE YEAR LIMITED WARRANTY Turbosmart is a company built on Customer Satisfaction and Service. That is why all of our produ

Comentarios a estos manuales

Sin comentarios